TherMiser control systems are designed to provide precise remote control of ThermaSkirt heating system, to closely maintain the desired room temperature and timings, providing a completely discreet heating system. Low surface temperature control for additional safety, or wireless multi-room zone control for ease of installation are also available.
Results from BSRIA Test Data to BSEN 442-1
@ Flow rate: 56g/sec
All test data based on powder coated white finish RAL 9010 to BS-EN 12206-1.
Urban LT Profile
(150mm/6" x 20mm)
Weight: 1.35kg/m
| Boiler Temp |
Watts/m |
BTU/m |
BTU/ft |
Dt50
(72°C flow) |
148.5 |
505 |
153 |
| 40°C |
46 |
149 |
48 |
| 45°C |
59 |
197 |
62 |
| 50°C |
73 |
245 |
78 |
| 55°C |
88 |
297 |
93 |
| 60°C |
104 |
350 |
110 |
| 70°C |
142 |
460 |
150 |
| 75°C |
159 |
517 |
168 |
|
|
Classic Torus TS Profile
(150mm/6" x 20mm)
Weight: 1.35kg/m
| Boiler Temp |
Watts/m |
BTU/m |
BTU/ft |
Dt50
(72°C flow) |
150 |
508 |
155 |
| 40°C |
47 |
150 |
49 |
| 45°C |
60 |
198 |
63 |
| 50°C |
74 |
246 |
79 |
| 55°C |
89 |
298 |
94 |
| 60°C |
105 |
351 |
111 |
| 70°C |
144 |
461 |
151 |
| 75°C |
160 |
518 |
169 |
|
|
Regency OG Profile
(200mm/8" x 20mm)
Weight: 1.65kg/m
| Boiler Temp |
Watts/m |
BTU/m |
BTU/ft |
Dt50
(72°C flow) |
170.78 |
690 |
177 |
| 40°C |
52.90 |
208 |
60 |
| 45°C |
67.85 |
275 |
74 |
| 50°C |
83.95 |
342 |
95 |
| 55°C |
101.20 |
416 |
115 |
| 60°C |
119.60 |
488 |
132 |
| 70°C |
163.30 |
643 |
185 |
| 75°C |
182.85 |
724 |
215 |
|
|
Deco Profile
(115mm/4.5" x 20mm)
Estimated subject to BSRIA test
Weight: 1.1kg/m
| Boiler Temp |
Watts/m |
BTU/m |
BTU/ft |
Dt50
(72°C flow) |
133.65 |
|
|
| 40°C |
41.40 |
|
|
| 45°C |
53.10 |
|
|
| 50°C |
65.70 |
|
|
| 55°C |
79.20 |
|
|
| 60°C |
93.60 |
|
|
| 70°C |
127.80 |
|
|
| 75°C |
143.10 |
|
|
|
|
“DiscreteHeat recommends an allowance of up to 3% to these outputs on exterior walls to allow for back losses. Further precautions may be required depending on the age and/or nature of the construction of the building – please contact DiscreteHeat for advice.”
|
|
ThermaSkirt ®
Material: Aluminium & Polymer Alloy
Thermal Conductivity: 236w/m2/K
Water Content 0.49l per m
Paint Finish: to BS EN 12206-1
Foil Finish (where applied) Renolit MBAS 0.15mm
Corrosion Resistance: Excellent
Oxygen Permeability: 0 (Negligible)
|
|
Connectors
Material: Non Hygroscopic Engineering grade polypropylene / Nylon mix
Oxygen Permeability: 0 (Negligible)
O Ring: Balanced Twin Shore Viton & Silicon Mix
Maximum Operating Pressure: 10bar (150psi)
Maximum Op. Temperature: (Greater than or Equal to) 130°C
|
|
Valves & Return Manifold
Material: Non Hygroscopic Engineering grade polypropylene / Nylon mix
Oxygen Permeability: 0 (Negligible)
O Ring: Balanced Twin Shore Viton & Silicon Mix
Maximum Operating Pressure: 10bar (150psi)
Maximum Op. Temperature: (Greater than or Equal to) 130°C
|
|
Connector Clips, Brackets & Fixtures
Punch pressed 306 Stainless Steel
Mounting Brackets (LT, TS & OG)
High Temperature Resistant Graphite Nylon
Covers & Corners
Ultra-stable temperature resistant ABS & UPVC
Foil Finish (where applied) Renolit MBAS 0.15mm
|
|
Yes - and it couldn’t be simpler!
Download our free ThermaSkirt® Designer Software and follow the simple steps to install it on your system. After the installation is finished, launch the design software to create your own ThermaSkirt® heating system - in minutes! It will even work out your heat loss calculation, heat output, temperature drop & flow resistance!
ThermaSkirt® can be supplied in pre-cut ready-to-install room kits, complete with a numbered room plan. Your installer can follow the step-by-step instructions supplied.
Alternatively, you can buy full 2M, 3M and 6M lengths and cut on site. Ask about our on-site training day.
Full set of instructions are available and can be downloaded from the Technical Information section of our website.